An economical and effective solution to isolate the house from noise and cold is the door molding. In this article, we’re going to explain the different types of weatherstrip you can find and how to install them.
Why is it necessary to put weather protection on the doors of a house?
Sucking in air from outside can lead to significant heat or cold losses from inside the house. Using this method of isolation reduces air intake by 10%.
So, one of the main reasons to put a weather bar on the door is Energy savings when heating in winter and cooling in summer.
By reducing the incoming air, the entry of dust and insects is also reduced. Preference for a cleaner and healthier indoor climate.
How do I know if the door has an air inlet?
To find out if there is an air inlet in the door, just raise your hand and slide it through. You can moisten your hand for greater sensitivity.
Another option is to bring a match, lighter, or burning candle to the frame and see if the flame moves or goes out. Another sure-fire way to find out if there is one Air intake in the frame or under the door is to put the room in the dark, close the door and turn on a flashlight outside.
If the light is filtered under and next to the door, it will be necessary to put on weather tape or some other method of isolation. Another method is to try a count between the door and the frame. If the ticket expires you will need to isolate yourself. Make sure you check it top down.
Some houses need to insulate the ceiling and walls, here you can consult a professional bricklayer.
Types of security strips for doors
Hard PVC adhesive burette
This type has a PVC strip with a brush on one side. Its main purpose is to prevent the escape of dust or dirt from the outside, as well as to prevent leakage from the inside and penetration from the outside.
They can be used on doors with a distance of 2 cm between the door and the floor.
Flexible PVC adhesive tape for weather influences
This model has a felt that guarantees water resistance. Can be used on doors with a ground clearance of less than 3 cm.
Weatherproof tape under the expanded PVC door
This model has an insulating rubber, with the advantage that it does not scratch the surface of the floor and offers better insulation against water.
Weather protection for garages and commercial blinds
The basin of this type of weather strip allows it to be placed on larger doors such as garages or shutters of commercial premises. The part that holds it to the door is usually made of aluminum that can be cut to size with a saw.
To optimize the attachment to the door, it has holes for screwing.
Tilt belts for the weather
This system is ideal for not scratching the floor as it has hinges that allow the bar to raise and lower over time. They come in a variety of designs that you can hide.
Double role
These models consist of a channel and a pad on each edge to protect the door edge inside and out. They are made of a very flexible material that allows it to be slid under the door.
There are other alternatives to insulate your home and make it more energy efficient. Here you can find professional reference prices.
How do I install a weather bar for the door?
The installation of the weather bar depends on the type purchased. However, the first step relates to preparing the surface on which it will be installed. This consists of wiping off any stuck dust with a clean, dry cloth. After spending a a towel soaked in alcohol, That way, he’s ready to place the timeline.
Adhesive tape for door weather
This type of seal is the easiest to use. Because you only have to measure the width of the door and cut the timeline to size with a saw, knife or scissors, depending on the material. Then remove the protective tape and press the waterproof strip firmly against the bottom of the door.
The brush or sponge must scrub the floor in order for it to function effectively.
Tape with screws
The first step is to measure the weather bar so that it lines up perfectly with the measurement on the door. If it doesn’t fit, it should mark and cut out with a saw, note that the cutting disc must be suitable for weatherproof material.
These gaskets, which have holes for the passage of screws, need to be presented on the door and we will start installing the screws.
Sealing strips on the door frame
Once the door frame is clean we start placing the weather strip, removing the protective strip and pressing the foam against the frame. When we get to the end we will squeeze the weather bar and cut it so that it is safe.
With these simple steps we are ready to insulate our home from the most extreme temperatures. In addition, you will enjoy a healthier and cleaner environment while saving energy.
A great trend that also protects us from low temperatures are Aluminum fences on balconies, terraces and barbecue areas.